Warning: THE VOID WIKI IS DEPRECATED. It is no longer being maintained, contains outdated and incorrect information, and will eventually be shut down. Please refer to the Void Handbook, https://docs.voidlinux.org/, for the official documentation. If you can't find the information you're seeking, please raise an issue at https://github.com/void-linux/void-docs/issues

Difference between revisions of "Network Configuration"

From Void Linux Wiki
Jump to navigation Jump to search
Line 173: Line 173:
Then restart the networkmanager:
Then restart the NetworkManager:
# sv restart NetworkManager
# sv restart NetworkManager

Revision as of 06:26, 8 August 2017

Static IP

Static IP configuration can either be done through dhcpcd and its configuration file /etc/dhcpcd.conf, or iproute commands in /etc/rc.local (see below). If an ethernet interface was configured at the installer, the dhcpcd.conf file should look as follows:

# Static IP configuration.
interface eth0
static ip_address=
static routers=
static domain_name_servers=

The dhcpcd service must be enabled in the default runlevel:

# ln -s /etc/sv/dhcpcd /var/service/

A simpler solution without the need of running the dhcpcd daemon would be to setup the network interface in the file /etc/rc.local via commands from the iproute package:

# Static IP configuration via iproute
ip link set dev eth0 up
ip addr add brd + dev eth0
ip route add default via

Dynamic IP (DHCP)

This is handled by the dhcpcd package and its service. To acquire a lease for any known interface simply enable the dhcpcd system service:

# ln -s /etc/sv/dhcpcd /var/service/

DHCP per interface

The default dhcpcd runit service works in all available network interfaces, but sometimes only a single interface needs to be setup, in that case we'll make another service with some modifications:

# mkdir -p /etc/sv/dhcpcd-eth0
# vi /etc/sv/dhcpcd-eth0/run
       exec dhcpcd -B eth0
# chmod 755 /etc/sv/dhcpcd-eth0/run
# ln -s /run/runit/supervise.dhcpcd-eth0  /etc/sv/dhcpcd-eth0/supervise

This new runit service will only work for the eth0 device. Now you just need to symlink it to the current runlevel to enable and start it:

# ln -s /etc/sv/dhcpcd-eth0 /var/service/

You can find available network devices by executing

# ip link

Desktop Network Daemons (NetworkManager, wicd and connman)

These applications conflict with the methods mentioned above so before using NetworkManager, wicd or conmman make sure that dhcpcd and wpa_supplicant services are stopped and disabled:

# rm -f /var/service/<foo>

or for the per interface service; make sure that none of these services are started by default.

Wireless (default)

Wireless connections are handled by the wpa_supplicant package; it can handle multiple kinds of security against the APs: none, WEP, WPA-PSK (WPA Personal), WPA-EAP (WPA Enterprise) and more.

Copy the wpa_supplicant.conf file to match your network device:

$ cp /etc/wpa_supplicant/wpa_supplicant.conf /etc/wpa_supplicant/wpa_supplicant-<device>.conf


Just edit /etc/wpa_supplicant/wpa_supplicant-<device>.conf and add the following lines:

# Default configuration file for wpa_supplicant.conf(5).
# Add your networks here.
    wep_key0="YOUR AP WEP KEY"

WPA-PSK (WPA Personal)

For WPA-PSK we must generate the pre shared key with wpa_passphrase(8):

$ wpa_passphrase MYSSID key

Just append the resulting output from the above command to /etc/wpa_supplicant/wpa_supplicant-<device>.conf:

# Default configuration file for wpa_supplicant.conf(5).
# Add here your networks.
    #psk="YOUR AP KEY"

Starting wpa_supplicant

You can now enable the dhcpcd service, which has a hook to start wpa_supplicant, and use the wpa_cli(8) command to see details of this AP connection.

Note: Behaviour changed in dhcpcd-6.10.0-1: The hook is not enabled by default anymore.

Check which version you are using ($ dhcpcd --version). If you're using 6.10.0-1 or newer you have to enable the wpa_supplicant hook:

$ sudo ln -s /usr/share/dhcpcd/hooks/10-wpa_supplicant /usr/libexec/dhcpcd-hooks
Note: Not sure if the following driver option in dhcpcd works anymore. Add -Dwext to your command if you find you have issues.
$ sudo wpa_supplicant -B -i<interface> -c<path/to/conf> -Dwext

If you happen to need a special driver (option -D) you can edit /etc/dhcpcd.conf and add a line like env wpa_supplicant_driver=wext.

After enabling this hook, don't forget to restart dhcpcd:

$ sudo sv restart dhcpcd

If wpa_supplicant is still not starting after this, try starting it from the command line with

$ sudo wpa_supplicant -i <device> -c /etc/wpa_supplicant/wpa_supplicant-<device>.conf

to see if you get any errors.

Wireless (NetworkManager)

Install required packages:

# xbps-install NetworkManager network-manager-applet gnome-icon-theme inetutils-ifconfig gnome-keyring

If you want messages about the state:

# xbps-install xfce4-notifyd

Disable dhcpcd and wpa_supplicant services:

# rm -fr /var/service/dhcpcd
# rm -fr /var/service/wpa_supplicant

Enable and start new services:

# ln -s /etc/sv/NetworkManager /var/service
# ln -s /etc/sv/dbus /var/service

Start nm-applet in the desktop manager start file:

nm-applet &

The applet should show up in the system tray. If your desktop manager doesn't have one, look for stalonetray or trayer-srg which are available in Void Linux.

Captive Portal Detection

NetworkManager support connectivity detection in captive portals. In VoidLinux this is default off. You can enable it by adding creating this file:

response=NetworkManager is online

Then restart the NetworkManager:

# sv restart NetworkManager

Connecting to hotel / restaurant / airport hotspots via the command line

Oftentimes, wifi hotspots in various public places don't have an accompanying WPA / WEP key. They require you to connect to their ESSID, obtain an IP address, and subsequently log in via a web interface of some sort. Here are two ways that will allow you to log into these networks.

Method 1: one-time connection

If you don't foresee yourself connecting to this network more than once, the following method is an effective way to connect to the establishment's network temporarily:

Step 1: stop the current dhcpcd service if it's running

$ sudo sv stop dhcpcd

Step 2: bring up your wireless NIC

$ sudo ip link set <device> up

Replace <device> with the name assigned to your wireless card. If you don't know its name, you can use the ip a or ip link command.

Step 3: connect to the ESSID of the establishment

$ sudo iw dev <device> connect -w "AwesomeHotel"

The -w option waits until the connection either succeeds or an error occurs.

Step 4: obtain an IP address from the network

$ sudo dhcpcd <device>

You should now be able to fire up your favourite web browser and log into the network normally.

Method 2: saving the connection

If you're staying at a hotel for a few days, you might want to save the connection details for the duration. This method uses the wpa_cli command to store the ESSID of the hotel in the /etc/wpa_supplicant/wpa_supplicant-<device>.conf file. This assumes that you have the wpa_supplicant service running. This won't work if the service isn't up. Once connected, the dhcpcd service will obtain an IP from the network if it too is running.

Step 1: start wpa_cli in interactive mode

$ sudo wpa_cli

At this point, wpa_cli will tell you which interface it's working on and greet you with a > prompt. If you want to specify the interface, simply include its name with the -i switch when starting wpa_cli:

$ sudo wpa_cli -i <device>

You might also see a bunch of unsolicited messages fly by as you move on to step 2.

Step 2: connect to the network and save the ESSID

> add_network
> set_network 12 ssid "The_hotel_SSID"
> set_network 12 key_mgmt NONE
> enable_network 12
> save_config
> quit

Enjoy your stay!

See also

  • dhcpcd(8), dhcpcd-run-hooks(8)